Service Menu

• 

• PWC / JET BOAT SERVICE

  • Inspect & replace spark plugs
  • Perform ECM computer diagnostics
  • Install new battery
  • Program DESS Key
  • Oil Change
  • Impeller and wear ring change
  • Impeller oil change

  Trailer Services

  • Single axle
  • Dual axle
  • Bleed and flush brake system
  • Lake test

PWC/JET BOAT MANUFACTURER'S RECOMMENDED MAINTENANCE

• • FOUR STROKE PWC
  • TWO STROKE PWC
  • FOUR STROKE JET
  • TWO STROKE JET
  • TWIN ENGINE JET OIL CHANGE ADDITIONAL
• • Inspect control cables (adjust if needed)
  • Inspect for water leaks
  • Inspect for oil leaks
  • Inspect for fuel leaks
  • Inspect battery and clean terminals
  • Inspect fuel lines
  • Inspect fuel filter for contaminants
  • Inspect fire extinguisher
  • Inspect starting system
  • Inspect all instrumentation

Perform The Following: Grease All zerk fittings, Change engine oil and replace oil filter (4-stroke only), *** NOTE: Engine oil should be replaced more frequently when operated under adverse conditions *** Perform general overall inspection of unit, Test run engine in shop

• 

• ATV / UTV SERVICE

  • Front & Rear differential fluid change
  • Inspect drive belt & clutches
  • Replace hub fluid if applies
  • Adjust Valve Clearance first cylinder
  • Adjust Valve Clearance 2nd cylinder
  • Brake fluid fluid
  • Inspect & replace spark plugs
  • Adjust chain and lube
  • Throttle cable lubrication
  • Spark arrestor cleaning @300 hours
  • CV Boot Replacement first boot
  • CV Boot Replacement Each additional boot

ATV/UTV MANUFACTURER'S RECOMMENDED MAINTENANCE

• Inspect brake pads
• Inspect coolant level & test hydrometer readings
• Inspect headlights & taillights
• Inspect Instrumentation gauges
• Inspect for coolant leaks
• Inspect for oil leaks
• Inspect for fuel leaks
• Inspect battery and clean terminals
• Inspect fuel lines, Inspect fuel filter for contaminants
• Inspect four wheel drive operations, Inspect tire condition
• Front tire pressure, Rear tire pressure
• Torque lug nuts
• Inspect CV boots for damage or wear
• Inspect and adjust throttle free play
• Inspect starting system
• Inspect gear shifter operation
• Inspect suspension
• Inspect operation of winch if applicable

Perform The Following: Grease All zerk fittings, Drain and replace transmission oil, Change engine oil and replace oil filter, Remove and clean air filter element, Perform ECM Computer diagnostics check if applicable, Perform general overall Inspection of unit, Test ride unit

• 

• Carbides Fits Ski-Doo & Polaris®

  • 4 Inch
  • 6 Inch
  • 8 Inch
  • 10 Inch

  * Please Note: Dual Carbides are extra, ask your service advisor for pricing

  Hyfax Fits Ski-Doo & Polaris®

  • Hyfax Replacement

• Chain Case Oil Replacement Ski-Doo & Polaris®

  • With Reverse
  • Without Reverse

  Power Valve Cleaning Ski-Doo & Polaris®

  • Power Valve Service
  • Extend Belt Life
  • "want to increase your belt life"
  • Perform clutch Alignment & Belt Deflection

  ALL BRAND 4 - STROKE OIL CHANGE

  • 4 - Stroke

• SNOWMOBILE SUMMARIZATION

  • Add fuel stabilizer
  • Run motor to run stabilizer through fuel system
  • Spray fogging oil through carburetor into engine (if Applicable)
  • Grease all accessible zerks
  • Drain fuel from carburetors and inspect fuel line
  • Inspect chain case oil
  • Inspect coolant condition (if equipped)
  • Inspect exhaust system
  • Inspect hyfax for excessive wear or damage
  • Inspect lights
  • Clean air filter if applicable
  • Disconnect battery & remove if requested
  • Inspect general condition of machine

SNOWMOBILE MANUFACTUER'S RECOMMENDED MAINTENANCE 2 STROKE

• Inspect Hyfax For Excessive wear and/or damage
• Inspect wear bars and advise
• Inspect Track shock condition and mounts
• Inspect Track and Hardware
• Inspect Front Suspension, skis and steering condition
• Inspect Ski Alignment and advise
• Inspect braking system including parking brake, (Top Off Fluid If Needed)
• Inspect Coolant Level and Condition, (Top Off if Needed)
• Inspect Fuel Lines and Filter
• Inspect and clean air filter element
• Inspect and adjust oil pump
• Inspect Chain Case oil and adjust chain tension to specs
• Inspect fan belt belt condition and tension (if equipped)
• Inspect all lighting
• Inspect drive belt wear and condition
• Visually Inspect clutch for Abnormal Wear
• Inspect exhaust system
• Inspect starting system
• Inspect all Instrumentation

Perform The Following: Grease All Zerk Fittings, Adjust Track Tension and Alignment, Perform General Overall Inspection, Test Run Engine In Shop

• 

• Stern Drive References

  • Inspect thermostat housing
  • Inspect & replace spark plugs
  • Replace water pump impeller in lower unit
  • Replace Water Impeller I/O
  • Prop Rebuild Aluminum
  • Prop Rebuild Stainless
  • Dual Battery Set-up
  • Gimbal Bearing, U-Joint & Bellows Inspection
  • All Bellows Replaced
  • Shift Bellows Replaced
  • Bilge pump install
  • Blower vent install
  • Trailer Services Single Axle
  • Trailer Services Dual Axle
  • Trailer Services

• Trailer Brakes Bleed and Flushed

  • Perform ECM Computer Diagnostics
  • Lake Test
  • Repaint Outdrive
  • Skeg Welding up

• PERFOM THE FOLLOWING

  • Grease All zerk fittings
  • Drain and replace gear case lubricant
  • Remove prop, lube splines
  • Tilt and Trim operation
  • Perform general overall Inspection of unit
  • Test run engine in shop
  • Change engine oil and replace oil filter

  ** NOTE: Engine oil should be replaced more frequently. When operated under adverse conditions

STERN DRIVE MANUFACTURER’S RECOMMENDED MAINTENANCE

• Inspect power trim & Steering fluid (Top off if needed)
• Inspect Flame resistor
• Inspect control cables (adjust if needed)
• Inspect serpentine belt for stretching and wear
• Inspect engine timing setup
• Inspect for water leaks
• Inspect for oil leaks
• Inspect for fuel leaks
• Inspect battery and clean terminals
• Inspect fuel lines
• Inspect fuel filter for contaminants
• Inspect corrosion control anodes
• Inspect fire extinguisher
• Inspect all lighting
• Inspect starting system
• Inspect all Instrumentation
• Inspect bilge and blower operations